Home » Posts tagged 'commercial deck repair'
Tag Archives: commercial deck repair
Deck Repair Charleston SC is often an inevitable part of owning a home. Weather damage, rock salt used to melt ice in the winter, and general wear and tear can all affect the appearance and safety of your deck.
If there is rot in weight-bearing posts or beams, this will cost more to fix than surface rotting on planks. A professional should inspect these areas before attempting any repairs.
Water damage can be a major problem for a deck. It can saturate the wood, weakening it and making it more susceptible to warping, splitting, mold growth, and other issues. It can also cause rot and termite problems.
The first step in repairing water damage is to find the source of the problem. This can be difficult, especially if you have a large number of boards. Start by checking the joists underneath the damaged board. If you see rot or other signs of moisture, remove the board and treat and protect the exposed joists.
Once the rot is taken care of, you can reseal the deck to protect it from future damage. You can choose to use a clear finish or a transparent stain. A semi-transparent stain is commonly recommended because it adds color while letting the grain of the wood show through.
After a few years, decks will lose their natural color due to exposure, wear and tear, and debris like stray leaves. Staining the deck can restore some of its color, and it will protect the deck from moisture damage and other potential problems.
Whether you choose to use a clear finish or sand and stain the deck, it is important to reseal it every year. This will help prevent water damage, which is the most common cause of deck failure.
If you have a lot of surface dirt and grime on your deck, wash it using a mild detergent solution and rinse thoroughly. Then sand the deck with a power sander or hand sander with 50-grit paper, making sure to sand with the grain.
Decks often have a railing or baluster that is loose, which can create a trip hazard. Loose railings can also allow water to penetrate the wood and cause rot. Repairing loose railings and securing loose balusters can improve safety and extend the life of the deck.
If you decide to replace a deck board, take a sample of the old and new boards with you to the lumberyard or hardware store so that you can match the color. This can be a time-consuming, but important step in getting your deck looking good as new again.
A deck that sits in the rain for too long or is covered with water for an extended period of time can experience mildew. This fungus can cause the wood to become soft and spongy, which will weaken it. Mildew is usually white or gray in color but can turn yellowish brown with age. It tends to grow on surfaces that are moist and warm.
It can also grow on fabrics, such as a towel that has been hung over a railing or a damp shower curtain left bunched up against the wall of a tub or the back of a door. Mildew is easy to remove with store-bought cleaners, but it’s important to get rid of the cause of the spores, too. Otherwise, the problem will just return.
Using a garden hose, wash your deck thoroughly and rinse it well to remove all soapy residues. Once the deck is dry, you can touch it up with a coat of CUTEK.
Mold and mildew both love warm, moist areas and can grow on a variety of items, from food to shower walls to regular old paper. They can also cause a range of health issues, including coughing, sore throats and respiratory problems in those with preexisting conditions.
One of the easiest ways to tell the difference between mold and mildew is by appearance and odor. Mold is typically black or dark green, fuzzy, and often grows in grotesque, raised shapes. Mildew is typically white, gray or yellow and has a powdery texture. It can sometimes grow in grotesque, raised shapes, but it is much less common than mold. It also has a musty scent that can be difficult to get rid of.
Both can be treated with a store-bought cleaner and a scrub brush, but mold is more difficult to get rid of than mildew. It’s especially important to keep fabrics as dry as possible, which is why it’s important to clean mildew-stained fabric immediately. If the stain has already gotten into the fibers of a fabric, it’s best to cut it out and toss the material.
A sagging deck is not only unsightly, but it can also be dangerous. If your deck sags more than a few inches in some places, it is likely to cause the ledger board (the long pressure-treated wood piece that attaches your deck to the house) to pull away from the house or even fall off. It’s possible to repair this problem on a DIY basis, but you should consult a professional if the damage is severe or extensive.
If your deck has a slight sag, try sanding the joists to help level them. You can do this with a power sander fitted with a fine-grit screen. You can also use a bar clamp or Deck Devil to apply pressure and pull up on the joists. If your joists are damaged, you may need to replace them. Joists can become bowed due to water damage, rot or insect damage, and rusted nails, screws or connections.
You should also inspect your deck for rotted posts. If you see signs of wood-eating pests on or around your deck, you should have them exterminated right away. These pests include termites, carpenter ants and woodpeckers. Insects like to eat away at wood, and if left unchecked can destroy the frame of your deck.
Most decks have large horizontal beams that rest on top of the support piers or posts and support the floor joists. Inspect these beams for severe cracks and water damage. You should also make sure that the beams are firmly attached to the piers or posts. If you can poke a finger into the beam and feel spongy wood fibers, you have serious rot and should replace it.
It is also important to make sure that the posts are firmly attached to the concrete footings. Posts that sit on the ground are more prone to sinking, especially in clay soils. The best way to prevent this is to either wait until the soil settles or dig the footings deeper to a solid, compacted layer of earth. This will prevent the sinking that can lead to deck failure.
When wood dries out, it shrinks and can leave the deck boards looking warped. This is a very common issue with wooden decks and can be easily fixed. Using the right technique, you can get your deck back to looking like new.
Decks are a beautiful addition to any home, but they also require regular care and maintenance. Without proper maintenance, they can develop problems that can lead to serious damage and deterioration of the structure. These issues range from mild to severe and can affect the appearance of your deck and the structural integrity of your home.
One of the most common causes of a deck collapse is that it has lost its structural integrity due to water damage. When a deck is properly constructed and maintained, it is designed to hold a large amount of weight without failing. However, if the structure has experienced serious water damage, it will start to sag and bow, which can cause significant safety risks for anyone who is using the deck.
If a deck is experiencing serious sagging and bowing, it is important to call in a professional to assess the situation and offer a solution. The professional can inspect the structure and determine if it is safe to use or if it will need to be replaced altogether.
Often, warped boards can be easily repaired by unscrewing them and flipping them over to create a smooth surface on the underside. It is then recommended to screw the boards back into place, making sure that there are screws every 4-6 inches on each side of the board. This will prevent the board from shifting again in the future.
Another way to prevent warping is to seal the ends of the deck boards. This will prevent moisture from being able to escape the sides of the boards, which can cause them to dry at different rates and lead to warping.
It is also important to check the footings of a deck on a regular basis. The footings are concrete pads that are installed under the deck posts to support the structure. If these are showing signs of cracking or discoloration, it is important to take action before the problem worsens.